Learn — By WATMM Desk —
Reamping explained: reamp boxes, impedance, and using it on guitars, synths and drums
Reamping means sending a dry track you already recorded back out through an amp, pedals or a room and recording the result. Here is why you need a reamp box between your interface and an amp, how impedance and level come into it, and how to use the trick on guitars, synths and drums.
Key facts
- Reamping plays a dry, already-recorded track back through external effects, an amp and cabinet, or a room, and records the result.
- The Reamp device was introduced in 1993; John Cuniberti filed the patent (US 6,005,950) in 1994 and sold the business to Radial Engineering in late 2010.
- A reamp box converts a balanced line-level signal into an unbalanced, high-impedance, guitar-level signal; Radial's passive ProRMP does this with a transformer that also isolates grounds.
- Feeding line level straight into a guitar amp can cause input-stage distortion, treble loss or boost, and ground-loop hum.
Reamping is recording a track dry, then later playing it back out of your interface through an amp, pedals or a real room, and recording what comes back. You commit to the performance now and to the sound later.
The one piece of gear that makes it work is a reamp box, and the reason you need one is impedance and level. The rest of this guide covers both, then the three places we think reamping earns its keep: guitars, synths and drums.
What is reamping?
Wikipedia's entry on re-amping describes it as a technique where a dry, previously recorded track is played back through external effects and a guitar amp and speaker cabinet, or a reverb chamber, and re-recorded. It started with electric guitar and now also covers synths, virtual instruments and drums.
The idea is older than the name. The same entry notes that Les Paul put a loudspeaker at one end of a tunnel and a microphone at the other to capture reverb. The word "Reamp" comes from a device introduced in 1993; engineer John Cuniberti filed the patent (US 6,005,950) in 1994 and sold the patent, trademark and business to Radial Engineering in late 2010. The term is now used generically.
The workflow
- Record a clean DI track. Plug the guitar into a DI box or your interface's instrument (hi-z) input. If the player wants to hear an amp while tracking, split the signal so the amp feeds their ears and the dry signal goes to the recorder. Radial's ProRMP page describes exactly this: record dry through a DI while the player hears the amp.
- Send the dry track back out. Route it to a spare line output on your interface, into the reamp box, then into the pedals and amp.
- Mic the amp and record a new track. Change the amp, pedals and mic position as many times as you like; the performance doesn't change.
Our home guitar recording guide covers the DI and mic side, and choosing an audio interface covers why you want a spare line output and a hi-z input.
Why you need a reamp box: impedance and level
An interface's line output and a guitar amp's input expect very different signals. Line outputs are usually balanced and run at a much higher level than a guitar pickup, which is unbalanced, low level and high impedance. The Wikipedia entry lists what happens if you plug one into the other directly: distortion in the amp's input stage, treble loss or boost, and ground-loop hum.
A reamp box fixes three things at once:
- Level: it brings line level down to guitar level, usually with a control so you can set how hard you hit the amp.
- Impedance: it presents the amp with a source that behaves like a pickup, so the amp and pedals respond the way they would to a real guitar. Radial says the ProRMP "converts the balanced line level source to a hi-z output for your amp."
- Ground: a transformer isolates the two sides. Radial says the ProRMP's transformer helps "eliminate troublesome ground loops that can often cause buzz and hum." The ProRMP is fully passive and needs no power.
Wikipedia adds that a typical reamp device is a reversed DI transformer with resistors that lower the level and raise the impedance, and that a passive DI with a 10k-ohm series resistor is an alternative. Our cables and connectors guide explains balanced and unbalanced connections if those terms are new.
Guitars
This is the classic use. Wikipedia lists amp distortion, reverb, compression, EQ and modulation added after the fact, and notes that a dry DI lets someone remix a track decades later. In practice it means you can track at night with headphones and decide on the amp sound on the weekend.
Synths and virtual instruments
Wikipedia notes that synths and virtual instruments are now reamped through amps and effects too. A soft synth sent through a real amp, a fuzz pedal or a spring reverb picks up movement and grit that is hard to get in the box. Set the reamp level low to start: a synth's output is often hotter and wider-range than a guitar's, and the amp will tell you quickly if it is too much.
Drums
For drums, the idea is to play the kit back through speakers in a room and mic that room. Wikipedia describes playing stereo drum tracks through room speakers to add depth while keeping the stereo image. This works with programmed drums as well; pair it with our drum programming basics and a small, lively room. Speakers in a room want a line or power-amp feed, not a reamp box; the box is for instrument amps and pedals.
What we think
Reamping is the cheapest way to stop agonising over tone while you record. A dry DI track costs nothing to capture, and it turns every amp decision into something you can undo. For home producers, we'd do it by default on every guitar part, even if you end up using an amp sim on the DI. The real amp pass is then a bonus you can do when there's a quiet hour and a borrowed amp.
The trap is skipping the box. A line output into a guitar amp "works" in the sense that sound comes out, and that is why people blame the amp for thin, harsh or hummy results. If you reamp more than once in a while, a passive reamp box is one of the better buys in a small studio. If you reamp once a year, a passive DI with a series resistor, as Wikipedia describes, is a reasonable stopgap.
We'd also push the drum and synth uses harder than most guides do. Programmed drums and soft synths are where a home mix sounds most "in the box," and a speaker in a hallway or a cheap amp is a quick way to get some air and dirt back in. Check timing after any reamp pass: the new track comes back a little late through the round trip, so line it up with the original before you start mixing.
Sources
- ProRMP passive reamper, Radial Engineering (primary source). Accessed 31 Oct 2026.
- Re-amping, Wikipedia. Accessed 31 Oct 2026.
Researched with AI assistance, written and checked by WATMM Desk.