Learn — By WATMM Desk —
Multitrack recording a live show: splits, recorders, audience mics and consent
How to multitrack a gig: where to take the signal from, how a mic splitter keeps the desk and recorder apart, what recorder to use, why audience mics matter, and the consent and venue rules to sort out before doors. Sources checked on 31 Oct 2026.
Key facts
- Multitrack recording captures several sound sources on separate tracks so each can be adjusted later in a mixdown.
- A microphone splitter divides one mic signal into several paths and isolates the outputs from each other to prevent ground loops.
- In the US, recording a live musical performance without the performers' consent is covered by 17 U.S.C. § 1101, with the same civil remedies as copyright infringement.
- Tapers typically record with condenser mics in the audience; the Grateful Dead created a tapers section behind the soundboard in the mid-1980s.
A stereo board mix of your gig sounds thin and lopsided, because it was built for the room and not for a recording. Multitrack recording fixes that. It captures each source on its own track, so the level and tone of each can be changed later and combined in a mixdown (Wikipedia). The trade-off is more planning and more gear before the show (Wikipedia). This guide covers the signal, the recorder, the room and the permissions.
Where the signal comes from
You have three options, from easiest to most robust:
- The desk's own recording output. Many digital mixers can send every channel over USB or a network card to a laptop. Ask the venue engineer what their desk supports. The catch is that you get whatever gain the engineer set for the room.
- A mic splitter. A splitter divides one mic signal into several paths, can supply phantom power, and isolates the outputs from each other to prevent ground loops (Wikipedia). One leg goes to front of house, one to your recorder, and neither engineer can wreck the other's levels.
- Your own small recorder. Fine for a duo or a small acoustic set. Zoom's H6essential, for example, records six tracks in 32-bit float from four XLR/TRS inputs plus its X/Y capsule, and can act as a USB interface while recording to its SD card (Zoom). 32-bit float means a peak that would clip a 24-bit file can usually be turned down afterwards, which matters when nobody is watching the meters.
For a full band, a split plus a dedicated interface and laptop (or a stand-alone multitrack recorder) is the usual answer. Record at the sample rate you mix at and name tracks before soundcheck, not after.
Audience mics are not optional
Close mics capture the instruments and miss the gig. Put at least a stereo pair facing the crowd, ideally away from the PA, so you can blend in applause and room sound. Tapers have done this for decades: a typical rig is condenser mics, phantom power, a preamp and a recorder, all battery powered and portable (Wikipedia). Expect the room mics to arrive a few milliseconds later than the close mics; nudging them into time in the DAW, or not, is a creative choice.
A pre-show checklist
- Send the venue a channel list and ask in writing whether you may record and take a split.
- Bring your own power plan; a recorder that reboots mid-set loses the song.
- Run a backup: a second recorder on the room pair, or a stereo board feed, costs little.
- Record soundcheck and listen on headphones before doors.
- Label the session with date, venue and set list for the people who mix it later.
Consent and venue rules
Recording a show is not just a technical question. In the US, anyone who records a live musical performance without the performers' consent falls under 17 U.S.C. § 1101, which applies the same civil remedies as copyright infringement (Cornell LII). Other countries have their own performers' rights; check yours. Even with the band's yes, the venue can set its own rules on taking a split or placing mics.
Taper culture shows the consent model that works. The Grateful Dead first tolerated audience recording, then created a tapers' section behind the soundboard in the mid-1980s, and some bands let tapers patch into the board (Wikipedia). Recording without permission is known as stealth taping, and bootlegging for profit breaks taper etiquette (Wikipedia). If other acts share the bill, get each of them to agree separately. A recording you can't release is just a big file on a drive.
What we think
Most bands record the wrong thing first. They obsess over the recorder and forget the two things that decide whether the record is releasable: the room mics and the paperwork. A cheap recorder with a good crowd pair and a signed "yes" from every act will beat a 32-channel rig with neither. Get permission by email a week out, rig the audience pair before anything else, and treat the close mics as the part that can be fixed in the mix.
One more opinion: always multitrack, even if you think you only want a stereo memento. Storage is cheap and a gig never happens twice. Our working rule is that a single extra recorder on the room is the best-value insurance in live music. That is a view, not a standard.
Related guides
- Livestream a gig for when the audience is online too.
- Backing tracks for live shows for splitting stems and click on stage.
- Field recording basics for mic technique outside the studio.
- Live streaming performances and rights for the rights side.
Sources
- Multitrack recording, Wikipedia. Accessed 31 Oct 2026.
- Audio signal flow, Wikipedia. Accessed 31 Oct 2026.
- H6essential, Zoom (primary source). Accessed 31 Oct 2026.
- Taper (concert), Wikipedia. Accessed 31 Oct 2026.
- 17 U.S. Code § 1101: Unauthorized fixation and trafficking in sound recordings and music videos, Cornell Law School Legal Information Institute (primary source). Accessed 31 Oct 2026.
Researched with AI assistance, written and checked by WATMM Desk.